Burkert Type 8630 Manuel d'utilisateur Page 58
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
56 - 8630
OPERATION AND CONTROLLER FUNCTIONS
Start the automatic adaptation of the positioner to the current operating conditions
X.TUNE
- Autotune for positioner
➔ Start the program for automatic parametrization of the TOP Control Continuous via the menu item
X.TUNE.
The following functions are initiated automatically:
• Adaptation of the sensor signal to the (physical) stroke of the valve used
• Determination of parameters of the PWM signals for driving the solenoid valves integrated in the
TOP Control Continuous.
• Setting of the controller parameters of the positioner. Optimization is done according to the
criteria: as short a correcting time as possible and simultaneously freedom from overshoot.
➔ Start AUTOTUNE by calling up X.TUNE in the main menu.
➔ Then depress the MANUAL/AUTOMATIC key for 5 seconds.
ADDFUNCT
See section
Configuring the supplementary functions.
➔ Jump over this menu item on first commissioning.
NOTE
The basic settings onthe TOP Control Continuous are made in the factory. On
commissioning, nevertheless, execution of X.TUNE is
absolutely necessary
. TOP Control
Continuous then determines automatically the optimum settings for the current operating
conditions.
If the supplementary function
X.CONTRL
is present in the main menu during execution of
X.TUNE
, the positioner dead band
X.CO DBND
is additionally determined automatically as
a function of the frictional behaviour of the positioning mechanism (see chapter
Supplementary Functions
-
X.CONTROL
).
NOTE
To cancel
AUTOTUNE
, operate both arrow keys at the same time and select
X.TUN BRK
.
Display Description
TUNE 5
Countdown from 5 to 0 start of
AUTOTUNE
TUNE 4
:
TUNE 0
¦ X.T INIT
Display of the autotune phase in progress at the moment
¦ X.T A1-P
(continuation is indicated by a rotating bar to the left of the
¦ X.T TOPN
display)
¦ X.T TCLS
:
TUNE-END
Flashing display ➞ end of
AUTOTUNE
X.ERR X
Message on occurrence of an error
(Indication right: Error number, see chapter
Maintenance
and controller fault rectification)
- Operating Instructions 1
- TOP Control 3
- Continuous 8630 3
- FIRST COMMISSIONING 4
- INSTALLATION 4
- DEVICE NET 7
- Appendix 8
- TABLE FOR POSITIONER 9
- TABLE FOR PROCESS CONTROLLER 9
- MASTER CODE 9
- 8 - 8630 10
- GENERAL NOTES 11
- ENERAL NOTES 12
- Safety notes 12
- Intended use 12
- Scope of delivery 13
- Master Code 14
- Transport, storage 14
- Disposal 14
- SYSTEM DESCRIPTION 15
- YSTEM DESCRIPTION 16
- Valve types 16
- Construction of 18
- TOP Control 18
- Continuous 18
- Operating as a positioner 21
- 4 … 20 mA 22
- 0 … 20 mA 22
- 0 … 10 V 22
- Example of process control: 24
- COMMISSIONING 35
- IRST COMMISSIONING 36
- Fluidic installation 36
- NSTALLATION 44
- Installation of the valve 44
- Clock + 48
- Clock 48
- OPERATION 53
- CONTROLLER FUNCTION 53
- Operating levels 54
- Configuration of the keys 55
- AUTOMATIC 56
- Description of the procedure 57
- - Autotune for positioner 58
- (Countdown) 59
- Configuration menu 61
- Setting of numeric values 62
- 8630 - 61 63
- Supplementary Functions 64
- CHA LIN 65
- Normalized position 66
- 8630 - 65 67
- Entering the fixed points: 67
- Setting range: 75 ... 100 % 68
- Setting range: 0 ... 25 % 68
- DIR.CRISE 69
- DIR.ARISE 70
- Split range 71
- Control range in 72
- X.CONTRL 74
- CODE 0000 75
- Entering the safety position 76
- Activating the binary input 78
- Configuration of the outputs 79
- Limit position 80
- DEV.X XXX 81
- LIM.X XXX 81
- Setpoint 81
- CAL.USER 84
- OPERATING THE PROCESS 91
- CONTROLLER 91
- Supplementary function 93
- P.CONTRL 93
- P.CO - DBND 95
- P.CO - PARA 96
- P.CO - SETP 96
- P.CO - INP 97
- P.CO - FILT 97
- (P.CO INP 4 - 20 A) 98
- P.CO SETP / SETP INT 99
- P.CO SCAL 100
- (P.CO INP FREQ) 100
- Teach-In funktion: 102
- UNITXXXX 102
- (P.CO INP PT100) 103
- (P.CO INP P1’P2) 104
- (option flow rate controller) 105
- P.CO LEAK 106
- P.CO TUNE 108
- Operation 109
- Program sequence 113
- Operating the process 114
- Operating mode AUTOMATIC 115
- Operating mode MANUAL 116
- Displays 117
- 116 - 8630 118
- PROFIBUS DP 119
- ROFIBUS DP 120
- Technical data 120
- General notes 120
- Interfaces 121
- Electrical connections 121
- Bus status display 129
- DEVICE-NET 135
- EVICENET 136
- Explanation of terms 136
- Electrical connection 138
- Configuration example 1 147
- Configuration example 2 150
- MAINTENANCE AND ERROR 153
- CORRECTION ON THE 153
- POSITIONER 153
- Maintenance 154
- PROCESS CONTROLLER 155
- P.Q'LIN 157
- Other malfunctions 158
- GENERAL RULES 159
- ENERAL RULES (APPENDIX) 160
- OPERATING STRUCTURE 171
- PERATING STRUCTURE (APPENDIX) 172
- TABLES FOR 179
- 178 - 8630 180
- 180 - 8630 182
- MASTERCODE 183
Produits connexes et manuels pour Accessoires pour l'eau Burkert Type 8630
(2 pages)
(16 pages)
(186 pages)
(188 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.733 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels