Burkert Type 8630 Manuel d'utilisateur Page 115
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8630 - 113
OPERATING THE PROCESS CONTROLLER
AUTOMATIC
mode
MANUAL
mode
or
(> 5 s)
Switch over
display
Menu item
Configuration
or
Release key
END
active
SP
No
operating
action
P.TUNE
(process tune)
ready for start
PV_____
SP_____
POS__XXX
CMD __XXX
TEMP__XX.X
and
Set the
process
setpoint
P.TUNE
(process tune)
(> 3 s)
Release
key
Displays
With the process controller activated, the following parameters can be displayed:
• Actual value of process variable (process value)
PV_____
(- 999 ... 9999)
• Setpoint of process variable (process setpoint)
SP_____
(- 999 ... 9999)
• Setpoint position of valve actuator after rescaling through
optionally activated split-range function or correction curve
CMD __XXX
(0 ...100 %)
• Temperature inside housing of the TOP Control Continuous
TEMP__XX.X
(in °C)
By pressing the arrow keys, you can switch between these display options.
In the AUTOMATIC mode, normal controlled operation is executed and monitored.
Meaning of the keys
Operating mode AUTOMATIC
Switch over the display
Change the process setpoint
With configured supplementary functions
P.CONTRL/P.CO SETP/SETP INT
and
SP
display set.
or
or
Operating structure and procedures
and
Make
P.TUNE
(process tune) ready for start.
With
PID
self-optimization activated,
P.CONTRL/P.CO TUNE/ P.TUN ACT
NOTE
> 3 sec
If the device is in the safety position (for the relevant configuration, see menu item
BIN-IN
or
SIG-ERR), SAFE XXX
appears in the display.
If the menu item
CUTOFF
is activated and the process vave is in the tight-closing range,
a flashing
MIN
or
MAX
symbol appears in the display.
If the process value (
PV
) is above or below the measurement range, a flashing bar
appears in the display.
- Operating Instructions 1
- TOP Control 3
- Continuous 8630 3
- FIRST COMMISSIONING 4
- INSTALLATION 4
- DEVICE NET 7
- Appendix 8
- TABLE FOR POSITIONER 9
- TABLE FOR PROCESS CONTROLLER 9
- MASTER CODE 9
- 8 - 8630 10
- GENERAL NOTES 11
- ENERAL NOTES 12
- Safety notes 12
- Intended use 12
- Scope of delivery 13
- Master Code 14
- Transport, storage 14
- Disposal 14
- SYSTEM DESCRIPTION 15
- YSTEM DESCRIPTION 16
- Valve types 16
- Construction of 18
- TOP Control 18
- Continuous 18
- Operating as a positioner 21
- 4 … 20 mA 22
- 0 … 20 mA 22
- 0 … 10 V 22
- Example of process control: 24
- COMMISSIONING 35
- IRST COMMISSIONING 36
- Fluidic installation 36
- NSTALLATION 44
- Installation of the valve 44
- Clock + 48
- Clock 48
- OPERATION 53
- CONTROLLER FUNCTION 53
- Operating levels 54
- Configuration of the keys 55
- AUTOMATIC 56
- Description of the procedure 57
- - Autotune for positioner 58
- (Countdown) 59
- Configuration menu 61
- Setting of numeric values 62
- 8630 - 61 63
- Supplementary Functions 64
- CHA LIN 65
- Normalized position 66
- 8630 - 65 67
- Entering the fixed points: 67
- Setting range: 75 ... 100 % 68
- Setting range: 0 ... 25 % 68
- DIR.CRISE 69
- DIR.ARISE 70
- Split range 71
- Control range in 72
- X.CONTRL 74
- CODE 0000 75
- Entering the safety position 76
- Activating the binary input 78
- Configuration of the outputs 79
- Limit position 80
- DEV.X XXX 81
- LIM.X XXX 81
- Setpoint 81
- CAL.USER 84
- OPERATING THE PROCESS 91
- CONTROLLER 91
- Supplementary function 93
- P.CONTRL 93
- P.CO - DBND 95
- P.CO - PARA 96
- P.CO - SETP 96
- P.CO - INP 97
- P.CO - FILT 97
- (P.CO INP 4 - 20 A) 98
- P.CO SETP / SETP INT 99
- P.CO SCAL 100
- (P.CO INP FREQ) 100
- Teach-In funktion: 102
- UNITXXXX 102
- (P.CO INP PT100) 103
- (P.CO INP P1’P2) 104
- (option flow rate controller) 105
- P.CO LEAK 106
- P.CO TUNE 108
- Operation 109
- Program sequence 113
- Operating the process 114
- Operating mode AUTOMATIC 115
- Operating mode MANUAL 116
- Displays 117
- 116 - 8630 118
- PROFIBUS DP 119
- ROFIBUS DP 120
- Technical data 120
- General notes 120
- Interfaces 121
- Electrical connections 121
- Bus status display 129
- DEVICE-NET 135
- EVICENET 136
- Explanation of terms 136
- Electrical connection 138
- Configuration example 1 147
- Configuration example 2 150
- MAINTENANCE AND ERROR 153
- CORRECTION ON THE 153
- POSITIONER 153
- Maintenance 154
- PROCESS CONTROLLER 155
- P.Q'LIN 157
- Other malfunctions 158
- GENERAL RULES 159
- ENERAL RULES (APPENDIX) 160
- OPERATING STRUCTURE 171
- PERATING STRUCTURE (APPENDIX) 172
- TABLES FOR 179
- 178 - 8630 180
- 180 - 8630 182
- MASTERCODE 183
Produits connexes et manuels pour Accessoires pour l'eau Burkert Type 8630
(2 pages)
(16 pages)
(186 pages)
(188 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.533 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels