Burkert Type 0413 Manuel d'utilisateur télécharger pdf

Operating Instructions Type 0413

Marking (example):

Body Material

PL = Polyamide Plastic

Seal Material

NBR = NBR

FKM = FKM

Circuit Function

G = 4-way

Recorder No.

Voltage / Frequency / Power Consumption

Maximum Pressure

Approvals

The valve is either approved as

General Purpose valve for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1 and 2

Operating Temperature T 6

FM approved as

Nonincendive for Hazardous Locations

Class I, Division 2, Group A, B, C, D

Class II, Division 2, Group F, G

Class III, Division 1 and 2

Operating Temperature T 4A

UL listed for Ordinary locations

CSA approved for Ordinary locations

See label on the valve.

Operating Instructions 0605/08_EU-EN_00893138

Table 1 Seal materials

Fluid Tempera-

tures [°F]

Buna "N" (B) FKM (F)

Air Fluid T.

Ambient

+ 14 to + 140

+ 14 to + 130

+ 14 to + 140

+ 14 to + 130

Neutral

gas

Fluid T.

Ambient

+ 14 to + 140

+ 14 to + 130

+ 14 to + 140

+ 14 to + 130

Design:

4-way solenoid valve, internally piloted, in the de-energized

condition port P connected to port B and port R connected to

port A. With manual override.

Seal Materials and Fluids handled:

See Table1.

Fluid and Ambient Temperature:

For Hazardous Locations Div. 1 (T6 rated)

Max. Ambient Temperature 104 °F (40 °C)

Max. Fluid Temperature 140 °F (60 °C)

For Hazardous Locations Div. 2 and Ordinary Locations:

See Table1.

Pressure Range:

Minimum pressure differential between inlet and outlet port is

15 PSI.

Maximum inlet pressure see label on valve.

Installation:

Installation position as required. Ensure exhaust outlets for

pilot valve and main valve remain unrestricted but protect

against entry of dust, water and foreign matter. Pipework

should be clean. Do not put any loads on coil unit. Pipework

should be supported and installed to prevent strain on valve

body. Fittings should be sealed with PTFE tape, max. torque

80 in-lbs. 1/4 inch trough holes are provided for mounting.

Maximum torque for mounting 25 in-lbs.

Voltage 12V or 24V

UL / UR valid with

class 2 power supply only

1 2

Résumé du contenu

Page 1 - UL / UR valid with

Operating Instructions Type 0413Marking (example):Body MaterialPL = Polyamide PlasticSeal MaterialNBR = NBRFKM = FKMCircuit FunctionG = 4-wayRecorder

Page 2 - Operating Instructions

Operating InstructionsWiring DiagramElectrical Connection Type 2509 Electrical Connection:Ensure supply voltage/frequency corresponds with that on lab

Plus de documents pour Accessoires pour l'eau Burkert Type 0413

Voir le document Burkert Type 0413 Manuel d'utilisateur

Burkert Type 0413 Manuel d'utilisateur (6 pages)

Commentaires sur ces manuels

Pas de commentaire

Burkert Type 0413 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Burkert Type 0413. Burkert Type 0413 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Accessoires pour l'eau Burkert Type 0413

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Burkert Type 0413